![mac ethernet shows self assigned ip mac ethernet shows self assigned ip](https://sc02.alicdn.com/kf/HTB1ckLYKXGWBuNjy0Fbq6z4sXXaA/205718828/HTB1ckLYKXGWBuNjy0Fbq6z4sXXaA.jpg)
You should see a DHCP request like the one above and a response. If laptop doesn't get IP address from pfSense take a look at the pfSense console. On pfSense console start a trace: tcpdump -i re0 -port 67 (where you will have to replace re0 by the system name of your LAN interface, it will be something like re0 or vr0 or vr1 or …)
![mac ethernet shows self assigned ip mac ethernet shows self assigned ip](https://blog.networkgeek.in/img/arp/arp4.png)
(Its not certain that straight through cables will work without the switch so use a switch to reduce the unknowns.) PfSense LAN NIC connected to switch connected to laptop. PfSense LAN IP: 192.168.1.x/24 with DHCP server enabled and a DHCP address range from 192.168.1.x/24 You seem to have tried a number of different configurations and its now not clear to me what is what. Is 172.17.67.3 the IP address of the pfSense LAN interface? If not, what has IP address 172.17.67.3 and why is your laptop trying to talk with it? This suggests that 172.17.67.3 is not connected to your laptop. It also shows a number of ARP requests for 172.17.67.3 with no response. The tcpdump output you posted shows a number of DHCP requests with no response (e.g. the DHCP server is turned on and all the settings look fine.ĭo you have DHCP server enabled on the pfSense LAN interface? Does the pfSense LAN interface have a static IP address? What the heck is going on? according the netgate instructions, my laptop should have been assigned an address from the DHCP server from the start. i observed on one of them that it was also getting a self-assigned address. I tried connecting the LAN port on the pfsense box to our switch and hooked up some of the other computers. I also couldn't look up any hostnames / access the internet yet… so again i manually assigned it a 172 address on the same subnet and was able to get the the web interface again. i reconnected the ethernet cable between my laptop and the pfsense box and my laptop still got a self-assigned address. address, etc., and completed the setup wizard, saved the changes, and restarted the pfsense box. I changed the internal IP of the pfsense box to some 172. after i manually assigned it an address on the correct subnet ('ifconfig eth0 192.168.1.23'), i was able to connect to the webserver of the first pfsense box () and go through the setup wizard, following the instructions that i got from netgate. unfortunately, my laptop's eth0 didn't receive an address from DHCP, instead it got a 'self-assigned address'… 169.whatever.
![mac ethernet shows self assigned ip mac ethernet shows self assigned ip](https://klang.com/blog/wp-content/uploads/2017/10/dante-recover-network-settings.png)
I plugged our uplink into the WAN port, linked together the two OPT1 ports, plugged my laptop into the LAN port, and turned on the two pfsense units. The 192.168.0.1 is the one which I access to check the settings, the other is 192.168.0.252.
MAC ETHERNET SHOWS SELF ASSIGNED IP MAC
so, i was planning on just using a single pfsense box and at least having the config mirrored to the second pfsense box. I have an Arris DG3270A cable modem and if I do a port scan it shows two separate MAC /IP addresses. however, because of the way our ISP's network is constructed, we couldn't accomplish it without purchasing some more hardware. Open up your internet browser and hit refresh.We purchased the 1u alix.2d3 dual server from netgate, it has two pfsense boxes and the idea was to configure them for failover. Select the DNS tab and input your DNS infoħ. Fill out the boxes according to your IP addressĥ. Click on your Ethernet connection and where it says “Configure IPv4:” use the drop-down box to select “Manually”ģ. Open up Network Preferences with your adapter and Ethernet connectedĢ. Click "OK" and check your Ethernet connection. If you have any other questions, please contact us at #1ġ) Disconnect your Multi-Port Adapter from your computerģ) Manually remove "USB 10/100/1000 LAN" from your Network by clicking the "-" symbolĤ) Plug your Multi-Port Adapter back into your computerĥ) Manually add in "USB 10/100/1000 LAN" to your Network Preferences by clicking the "+" symbolĦ) After adding your Ethernet back in, please click on "Advanced" tabħ) In the "Advanced" tab, click on "Renew DHCP Lease" buttonĨ. If you entered your IP address manually, make sure you entered the correct address. Close all open apps and restart your computer. Put your computer to sleep, wait a few minutes, then wake it from sleep. If your issues still persist, move onto Set #2. Close the app that is using the connection (such as Safari or Messages), then open the app again. Follow Set #1 first and test your Ethernet again. Please note there are two sets of troubleshooting instructions. However, if you are experiencing any issues with your Ethernet connection, please follow the steps below. We hope you are enjoying your new Multi-Port Adapter!